The low stage of a cascade ultra-low-temperature system is charged with R-23, a refrigerant that boils far below the range used in ordinary air conditioning work. Which certification does a technician need to service that low stage?
Correct Answer
B) Type II, because that certification covers very high-pressure appliances along with ordinary high-pressure appliances
Appliances are grouped by the boiling point of the refrigerant at atmospheric pressure. Refrigerants that boil far colder than the ordinary high-pressure group put an appliance in the very high-pressure class. There is no fourth technician exam for that class. The Type II certification covers both high-pressure and very high-pressure appliances, with small appliances and motor vehicle air conditioning carved out. So a technician holding Core and Type II may work on the cascade low stage. The extremely cold operating temperature does not make the machine low pressure; it makes it the opposite.
Why This Is the Correct Answer
Very high-pressure appliances form their own equipment class in the definitions, but they do not get their own technician certification. The rule assigns high-pressure and very high-pressure appliances together to Type II, so one card covers both. Candidates who assume every equipment class has a matching exam are the ones who miss this.
Why the Other Options Are Wrong
Option A: Type III, because the extremely low operating temperature places the machine in the low-pressure class alongside the chillers
Low pressure means the refrigerant boils above room temperature, so the machine sits in a vacuum, which is the chiller family. A refrigerant boiling near a hundred below zero produces the highest pressures on the floor, not the lowest.
Option C: Type I, because a cascade low stage carries a small charge and is sealed at the factory like a small appliance
Charge size alone does not create Type I status. A cascade low stage is field-connected equipment with service ports, so it was never manufactured, charged and hermetically sealed at the factory the way a small appliance is.
Option D: A separate very high-pressure endorsement, taken as a fourth exam after the Type II exam is passed
No fourth technician exam exists. Very high-pressure appliances are folded into the Type II category rather than carrying an endorsement of their own, so the Type II card already reaches this machine.
Memory Technique
Three exams, four equipment classes. Very high pressure has no exam of its own - it rides in Type II's truck.
Reference Hint
40 CFR 82.161: Type II applies to high-pressure and very high-pressure appliances other than small appliances and MVACs. Very high pressure is defined by an extremely low atmospheric boiling point in 40 CFR 82.152.
More epa-608-type-2 Questions
A walk-in cooler condensing unit holds a full charge of twenty-five pounds of R-404A, which is below the fifty pound threshold that brings an appliance under the leak repair provisions. What still applies to this unit?
An office building has thirty water source heat pumps on a common water loop, and each one left the factory assembled, hermetically sealed and charged with four pounds of R-410A. How is one of those units classified?
A data sheet for an unfamiliar refrigerant lists a boiling point of about fifty-five degrees Fahrenheit at atmospheric pressure. What does that tell a technician holding Core and Type II certification?
A technician holds Core, Type I and Type III certification and is sent to recover the charge from a twenty ton rooftop unit charged with R-410A. What does that combination of sections allow on this job?
A fleet garage technician holds only the vehicle air conditioning certification issued under Section 609 and is asked to recover the charge from the shop's own rooftop air conditioner. What does that credential allow?
A split system's outdoor unit, indoor coil and the line set the installer ran and brazed between them are being considered. For the purposes of the refrigerant rules, what makes up the appliance here?
On a new installation the line set is brazed to a factory charged outdoor unit and an indoor coil shipped under a nitrogen holding charge, with the outdoor unit's service valves still closed. What does the recovery requirement call for before that brazing?
A rooftop unit's data plate has weathered until the charge figure cannot be read, and the technician needs the full charge to place the appliance under the evacuation and leak provisions. Where should that figure come from?
A computer room air conditioning unit holds forty pounds of R-407C and connects to a remote air cooled condenser through refrigerant piping run and brazed by the installer. How is that unit classified?
A shop's office manager, who holds no technician certification, is sent to a supply house to pick up a new recovery machine for the commercial crew. What does the sales restriction require at that counter?
People Also Study
Business & Financial Management
120 questions · 70% to pass
Contract Administration
60 questions · 70% to pass
Project Management
60 questions · 70% to pass
Related Study Resources
Previous Question
After the required evacuation level has been reached and the repair is finished, many technicians keep pulling the system down to a few hundred microns before charging. What is the standing of that deeper vacuum?
Next Question
A technician front seats the suction and discharge service valves on a semi-hermetic compressor, isolating it from the rest of the system. What has to happen before the compressor is unbolted and lifted out?